Red-and-white chimneys rising vertically against blue sky and clouds
In the alkaline cleaning line the spray piping circulates continuously, the shear at the nozzles beats the alkali liquor into fine dense foam, the liquid level in the rinsing section rises falsely in step, alkali mist carried out by the workpieces leaves white marks after drying, and the replenishment and rewash frequency of the whole line climbs shift by shift.
Chemi Tech supplies the KM214 series of defoamers for the foam conditions of alkaline spray cleaning lines and rinsing sections; the dosage is adjusted flexibly by spray pressure, alkali concentration, rinsing flow and line speed. This grade acts fast and resists strong alkali; it does not break emulsion in the high-shear zone of the nozzles and neither strips oil from workpiece surfaces nor leaves marks. The measured data on the foam-layer height in the spray section and the liquid-level reading in the rinsing section are recorded side by side at the same line speed, and the fitted dosage of the KM214 series is determined accordingly; the dosage of that line is set only after spray pressure and alkalinity grades are listed separately.
Advantages of Chemi Tech Defoamers
The Chemi Tech KM214 series defoamer is configured for alkaline spray cleaning lines and rinsing sections. It resists strong alkali, and its foam-suppressing ability does not decay as the spray-liquor alkalinity rises; it acts fast, breaking the fine bubbles generated in the high-shear zone of the nozzles at once; it breaks foam quickly, bringing the foam-layer height in the spray section down in a short time; it is compatible with the spray cleaner in the same bath without disturbing detergency and leaves no alkali marks on workpiece surfaces; the dosage is economical, rated by spray pressure and alkalinity, so the chemical cost per tonne of workpieces can be accounted shift by shift; and it is highly stable, so the liquid-level reading in the rinsing section does not fluctuate with the foam.
Industry Pain Points and Solutions
The root of foaming in an alkaline spray line lies mostly in the combined effect of shear entrainment from too-high spray pressure and alkali accumulation, while the alkali liquor returning from the rinsing section carries the fine bubbles back to the nozzles, finally concentrating in two places: a raised foam layer and a falsely high rinsing level.
After the spray pressure is raised, the fine bubbles in the nozzle zone are forced into the circulation piping and the foam layer first thickens in the spray section. KM214 resists strong alkali and acts fast; once the two readings of pressure and alkalinity are cleared, its dosage is re-rated by that line speed, and the foam-layer height falls back accordingly.
After the alkali concentration is switched, the same dosage gives markedly different foam-breaking speeds at two alkalinity grades. KM214 resists strong alkali; with the foam half-life at the low-alkali and high-alkali grades compared side by side, the gap from twenty-five seconds to forty-one seconds narrows to within five seconds, and the dosage is rated to the fitted grade of that line.
The returning alkali liquor from the rinsing section brings stable fine bubbles back into the spray zone and the foam-suppressing margin is consumed step by step. The KM214 series adds no extra water-replenishment frequency on this item; once pressure, alkalinity and flow are all checked through, the fitted dosage of that line is made clear and the spray shift doses at that grade.
Typical Operating Conditions and Verification
Customer case: the spray cleaning line of a metal surface-treatment enterprise in Zhejiang, applied to foam control in the alkaline washing and rinsing sections.
At this plant the foam layer in the spray section once covered half of the observation window, the rinsing level had to be checked manually twice per shift, and the white marks on workpieces after drying were more obvious on aluminium-alloy parts. KM214 was set as the replacement solution after comparison against the two readings of spray pressure and alkalinity, with the dosage rated by rinsing flow and line speed. After commissioning, the foam layer in the spray section receded below the lower edge of the observation window; the difference between the rinsing level and the on-site flow meter fell to within one division; the white-mark rating on workpieces dropped from grade three to grade one; and manual checks fell from twice per shift to once per day.
Frequently Asked Questions
Will a defoamer used in a spray cleaning line affect the surface state of workpieces in the rinsing section?
The starting points are two clues: spray shear and alkali accumulation. The KM214 series resists strong alkali and acts fast; it is compatible with the spray cleaner in the same bath without disturbing detergency, and the measured data on foam-layer height and rinsing level are given side by side by Chemi Tech at two alkalinity grades, so dosing at the rated magnitude leaves no alkali marks on workpiece surfaces. The actual dosage is corrected by line speed and rinsing flow; Chemi Tech derives the fitted dosage from comparison of the readings in the spray and rinsing sections.