Bundles of metal wire stacked diagonally into fine dense patterns
The brush-applied anti-corrosion topcoat levels poorly on steel-structure vertical surfaces: the panel edges first retract into sawtooth shapes, orange peel then surfaces across the wet film, brush marks remain on the paint film after drying, and interlayer adhesion fails the cross-cut test, so rework pins the coating shift's plan down at the topcoat step.
Chemi Tech supplies the KMP-2305 series of levelling agents for steel-structure anti-corrosion coating enterprises; the dosage is adjusted flexibly by wet-film thickness. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully after brushing; its compatibility is excellent and causes no craters, while leaving margin at the recoat interface. The measured results of the orange-peel grade on the panel surface and the cross-cut adhesion grade are filed into the same test-panel record, and the fitted dosage of the KMP-2305 series is settled at that grade of the line; the specific dosage is checked only after the brushing tempo and film-thickness grade are set.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-2305 series levelling agent is configured for the brush-coating levelling of steel-structure anti-corrosion topcoats. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; edge retraction at panel edges basically no longer appears, with even coverage at corners; the orange-peel grade on the panel surface rises and brush marks on the paint film become shallower in step; its compatibility is excellent, causing neither craters nor impairment of interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass brushing stable; and its thermal stability is strong, with no decomposition or yellowing in the ambient-temperature curing section and little effect on gloss.
Industry Pain Points and Solutions
The root of orange peel in brush-applied steel-structure topcoats lies mostly in the combined effect of a too-short flash-off window and a too-steep surface-tension gradient in the wet film, while vertical-surface brushing compresses the spreading time further, finally concentrating in two places: edge retraction at the panel edges and orange peel on the panel surface.
Once the brushing tempo is raised, the wet film has no time to spread within the flash-off window and the orange peel sets first. KMP-2305 markedly lowers the dynamic surface tension; once the tempo and flash-off temperature are set, its dosage is re-rated by the application speed on that vertical surface, and the orange-peel grade on the panel surface rises one notch.
When the wet film is set thicker, the surface-tension gradient at the panel edge amplifies and edge retraction follows, with film thickness at corners falling in step. KMP-2305 performs stably across thick-film and thin-film grades; with wet films of eighty and one hundred and twenty microns compared side by side, the retraction width narrows from three millimetres to half a millimetre, and the dosage is graded accordingly.
The interlayer interface between topcoat and primer is the most easily disturbed. The KMP-2305 series leaves margin for recoatability and adds no extra sanding step on this item; once tempo, film thickness and flash-off are all checked through, the fitted dosage of that vertical surface is settled and the coating shift executes at that grade.
Typical Operating Conditions and Verification
Customer case: the anti-corrosion coating workshop of a steel-structure engineering enterprise in Hebei, applied to the brush-coating stage of the topcoat on outdoor components.
At this plant, edge retraction on outdoor components recurred on vertical surfaces, orange peel varied from slight to severe on the same test panel, and the cross-cut result of the two-pass brushing passed only at the thin-film grade. KMP-2305 was selected as the levelling grade for that line after comparison of tempo and wet-film thickness, with the dosage rated by flash-off temperature and film thickness. Measured performance after the switch: the orange-peel grade on the panel surface rose one notch; edge retraction at panel edges basically no longer appeared; the cross-cut result of the two-pass brushing passed stably; the count of reworked parts fell back, and the coating shift completed its on-duty plan to the original schedule.
Frequently Asked Questions
If the levelling-agent dosage is raised in an anti-corrosion topcoat, will it cause craters or impair interlayer adhesion?
The three readings of edge retraction, orange-peel grade and cross-cut result must be checked together. The KMP-2305 series has excellent compatibility and causes no craters at normal dosage, leaving margin at the recoat interface; the measured data on orange-peel grade and gloss readings are checked out by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The actual dosage is further calibrated by brushing tempo and wet-film thickness; Chemi Tech checks the test-panel results against the on-site records and gives the fitted dosage.