Aerial view of plant units and pipelines

A water-based anti-corrosion coating's anti-rust pigment is milled in the bead mill until the fineness will not drop further, yet the discharged slurry settles into a hard block after one night of standing, and surface bleeding and a gloss gap appear together on the same re-inspection sheet.

Chemi Tech supplies dispersants for the dispersion of inorganic pigments in water-based anti-corrosion coatings, drawn from the dispersant KMK-201 series; the dosage is set flexibly by pigment oil absorption and grinding solids content. KMK-201 is a water-based dispersant whose anchoring groups grip the inorganic pigment surface and do not detach under high-shear milling. From measured data on grinding fineness and storage sedimentation, Chemi Tech grades the fitted dosage for the KMK-201 series.

Advantages of Chemi Tech Dispersants

Chemi Tech dispersant KMK-201 series is configured for inorganic pigments such as zinc phosphate, micaceous iron oxide and precipitated barium sulphate. Anchoring is stable, so pigment particles do not detach under high-shear milling and the fineness reaches the target grade faster; the viscosity-reduction effect is marked, so a high-pigment-loading slurry still flows and the bead-mill current stays steady; anti-settling performance is good, with no hard block in storage and the kettle stirring back to usable after opening; compatibility with water-based emulsions is excellent, with no coagulation or coarse-particle return; gloss and hiding power stay stable, and the re-inspection data no longer drifts; and the dosage is economical, graded by pigment oil absorption, so the number of re-ground batches falls.

Industry Pain Points and Solutions

The problem of anti-corrosion pigment dispersion mostly has its root in the combined action of an inadequate match between the pigment particle-size distribution and the dispersant's anchoring groups, while the low viscosity of the aqueous system also struggles to hold the particles, and it finally concentrates in two places: fineness rebound and storage sedimentation.

Once the shear applied by the bead-mill media rises, fine particles that are not anchored re-agglomerate and the fineness reading walks back up. KMK-201's anchoring is stable and it does not detach under high shear, so the fineness reaches the target grade already in the grinding stage.

Zinc phosphate is on the dense side, and when dispersion is insufficient the particles bridge with each other in storage and a hard block forms at the kettle bottom. KMK-201's anti-settling performance is good, keeping the pigment suspended through storage so it stirs back to usable on opening.

Re-milling and downgrading the slurry both land in the cost per tonne of anti-corrosion coating. Grading the dosage by pigment oil absorption and grinding solids content keeps additive spending inside a calculable range, and the number of re-ground batches falls with it.

Typical Operating Conditions and Verification

Customer case: an anti-corrosion coating enterprise in Jiangsu, applied to the grinding section of water-based epoxy and water-based acrylic anti-corrosion paints.

The bead mill ran three full passes yet the fineness still hovered around the pass line. A hard block formed at the kettle bottom within a week. The re-inspection gloss reading drifted batch by batch. The fitted points were settled: the grade set to KMK-201; the dosage graded by pigment oil absorption and grinding solids content in separate bands; replenishment adjusted with the batch formulation. After introduction, the fineness reached the target grade by the second pass; no hard block formed at the kettle bottom after two weeks of storage; and the re-inspection data for gloss and hiding power converged.

Frequently Asked Questions

Switching to a different anti-rust pigment, should the dispersant dosage be re-graded?

First see whether the pigment particle size and surface treatment fall in the same band. KMK-201 has completed comparative measured tests of grinding fineness and storage sedimentation across three inorganic-pigment classes, zinc phosphate, micaceous iron oxide and precipitated barium sulphate; within the recommended range the fineness is stable and no hard block forms at the kettle bottom. In practice the dosage is based on pigment oil absorption, with grinding solids content and formulation pH as correction terms; Chemi Tech verifies by comparing fineness reading against sedimentation height, and gives the fitted range.