Dark metal coils standing upright in closely spaced vertical rows
After automotive refinish paint is sprayed, the wet film has not spread within the flash-off window, orange peel on the panel surface and edge retraction at the corners appear together, the interlayer adhesion of the two-pass spray fails the cross-cut test, and rework and touch-up spraying pin the throughput down at the spraying step.
Chemi Tech supplies the KMP-1502 series of levelling agents for automotive refinish spray systems; the dosage is adjusted flexibly by the flash-off time. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the limited flash-off window; its compatibility is excellent and it causes no craters, while leaving margin for recoatability. The measured results of the orange-peel grade on the panel surface and the gloss readings are filed into the same test-panel record, and the dosage of the KMP-1502 series is settled at that grade of the line.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-1502 series levelling agent is configured for spray levelling of automotive refinish paint. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; edge retraction at panel edges basically disappears, with uniform corner coverage; the orange-peel grade on the panel surface rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters and not impairing interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass spray stable; and the additive cost per vehicle is rated by the flash-off time grade.
Industry Pain Points and Solutions
The root of orange peel in refinish spraying lies mostly in the combined effect of a too-short flash-off window and too-steep a surface-tension gradient across the wet film, while fluctuations in the spray-booth temperature further compress the spreading time, finally concentrating in two places: orange peel on the panel surface and edge retraction at the panel edges.
When the flash-off window is too short, the wet film has no time to spread in the levelling section and the orange peel sets first. KMP-1502 markedly lowers the dynamic surface tension; once the two readings of flash-off time and spray-booth temperature are set, its dosage is re-rated by the tempo of that line and the orange-peel grade on the panel surface rises one notch.
When the film thickness is set thicker, the surface-tension gradient at the panel edge amplifies and edge retraction follows, while the film thickness at corners falls in step. KMP-1502 performs stably across both thick-film and thin-film grades; once the two sets of readings of wet-film thickness and flash-off time are cross-checked side by side, the dosage is graded accordingly and edge retraction at the panel edges basically no longer appears.
The stability of the recoat interface must likewise be checked together. The KMP-1502 series leaves margin for recoatability and adds no extra sanding step on this item; once the three items of flash-off time, film thickness and spray-booth temperature have been checked through, the dosage of that spray line is settled accordingly and the coating workshop executes at that grade.
Typical Operating Conditions and Verification
Customer case: the refinish spray booth of an automotive coating service enterprise in Guangdong, applied to topcoat spraying and the flash-off levelling stage.
At this coating company orange peel recurred on the same batch of refinish parts, gloss uniformity stayed low after baking, and the cross-cut result of the two-pass spray was good on some panels and poor on others. KMP-1502 was used as the levelling agent for that spray line, with the dosage rated by flash-off time. Measured performance after the switch: the orange-peel grade on the panel surface rose one notch; edge retraction at the panel edges basically no longer appeared; the cross-cut result of interlayer adhesion for the two-pass spray passed stably; the count of reworked and touch-up parts fell back, and the spray section's shift plan was completed to the original schedule.
Frequently Asked Questions
If the dosage of the refinish levelling agent is increased, will it instead cause craters or impair recoating?
What must be worked out clearly is the degree of wet-film spreading within the flash-off window and the change in the orange-peel grade. The KMP-1502 series has excellent compatibility and causes no craters at normal dosage, leaving margin at the recoat interface; the measured data on orange-peel grade and gloss readings are checked out by Chemi Tech from the test-panel records of the same coating line. The actual dosage is re-calibrated by the flash-off time; Chemi Tech checks the test-panel results against the production-line records and gives the dosage of that line.