Close-up of water droplets scattered on dark umbrella fabric

Outdoor-jacket fabric leaves the finishing line with an acceptable rain-repellency rating, yet after several wash cycles the beads seep along the warp and weft seams under the coating; the damp stains on the shoulders and cuffs join into patches, and the returns and rework of finished garments pile up together by quarter-end.

Chemi Tech supplies the KMF-803 series of waterproofing agents for polyester and nylon outdoor fabrics; the dosage is adjusted flexibly by substrate grammage and wet pick-up. This grade forms a continuous film on the fibre surface, stays soft without stiffening or harsh hand, and is well compatible in one bath with resin softeners. The measured rain-repellency rating and hydrostatic-pressure data are read against each other, and the applicable dosage of the KMF-803 series is then given.

Advantages of Chemi Tech Waterproofing Agents

The Chemi Tech KMF-803 series waterproofing agent is configured for the water-repellent finishing of polyester and nylon outdoor fabrics. It forms a continuous film on the fibre surface, so beads roll off the fabric as droplets without spreading; the hand is soft, and the finished fabric does not stiffen or feel harsh, with no noticeable rustle during wear; it is well compatible in one bath with resin softeners, so no separate bath is needed for the finishing liquor; its wash resistance is good, and after repeated washes the rain-repellency score still falls within the customer's acceptance threshold; the hydrostatic-pressure rating meets the standard, and seepage at seams and needle holes is brought under control; and the dosage is economical, set against substrate grammage, so the replenishment rounds of the finishing liquor fall away.

Industry Pain Points and Solutions

The root of water-repellent decay on outdoor fabrics lies mostly in the combined effect of incomplete spreading of the finishing liquor over the fibre surface and insufficient curing temperature, while the one-bath competition from the softener also occupies part of the film-forming sites, finally concentrating in two places: the rain-repellency score and the hydrostatic-pressure resistance.

At low wet pick-up the finishing liquor distributes unevenly, leaving uncovered gaps on the fibre surface. KMF-803 forms a continuous film on the fibre surface, the fabric's rain-repellency rating recovers, and the beads roll off again as droplets.

When the curing temperature is insufficient the cross-linking is incomplete, and the film sheds first after washing. Once the substrate grammage and curing temperature are both checked, KMF-803 dosage is set by wet pick-up, and the score decay after washing eases.

The softener and the waterproofing agent compete for the attachment sites on the fibre surface, and neither the hand nor the repellency reaches the target. With the dosage set by substrate grammage, the one-bath compatibility with the softener no longer crowds each other out, and both the hand and the rain-repellency score stay on the acceptance sheet.

Typical Operating Conditions and Verification

Customer case: an outdoor-fabric finishing mill in Fujian, applied to the pad-finishing stage of hard-shell and soft-shell jacket fabrics.

The rain-repellency rating passed when the fabric left the line; the submitted samples wetted first at the shoulders and cuffs after repeated washes; and the damp-stain feedback from the garment factory clustered on the same batch of cloth. The mill settled its repellent component on KMF-803, with the concentration set by wet pick-up and curing temperature, adaptable to both pad and dip processing. Thereafter the fabric's rain-repellency rating returned within the customer's acceptance threshold; the score decay after washing eased; the hand stayed soft, and the garment factory's follow-on orders were booked into the next quarter.

Frequently Asked Questions

Used in one bath with a softener, will the waterproofing effect be dragged down by the softener?

First see whether the ionic type of the softener and the waterproofing agent fall within the same compatibility interval. KMF-803 has already completed comparative measured tests of rain-repellency rating and hydrostatic pressure on polyester and nylon outdoor fabrics; within the recommended range it is well compatible in one bath with common resin softeners, and the repellency score is not dragged down. The dosage is calculated by substrate grammage, with wet pick-up and curing temperature converted separately; Chemi Tech determines it by reference to the comparison of rain-repellency rating and hydrostatic pressure.