Rolled coloured fabrics stacked on a finishing table

After many rounds of use, the spray rating of upholstery and sofa fabrics falls grade by grade, waterborne stains wick inward along the seams, and re-washing and touch-up finishing put the delivery date under pressure at the finishing stage.

Chemi Tech supplies the KMF-4301 series of water repellents for the water-repellent and stain-resistant finishing of home-textile fabrics; the dosage is adjusted flexibly by substrate grammage, wet pickup and curing temperature. This grade forms a continuous film on the fibre surface, does not seal the original breathable channels of the fabric, causes no emulsion breaking when used in the same bath as the softener in the finishing liquor, and the film withstands many rounds of washing after curing. The measured data on AATCC 22 spray rating and hydrostatic pressure resistance are compared side by side, and the fitted dosage of the KMF-4301 series is graded from them.

Advantages of Chemi Tech Water Repellents

The Chemi Tech KMF-4301 series water repellent is configured for the finishing stations of upholstery and sofa fabrics. Its film formation is continuous, so the capillary channels at the seams are fully covered; the water-repellency grade is stable, so the fall in spray rating after many washes stays controllable; its stain resistance is good, so waterborne stains left on the fabric surface are easy to wipe off; its compatibility is excellent, with no emulsion breaking in the same bath as the softener; the dosage is economical, graded by substrate grammage; and fabric hand feel and breathability stay stable after curing.

Industry Pain Points and Solutions

The root of declining water repellency in home-textile fabrics lies mostly in the combined effect of low wet pickup and insufficient curing temperature, while the capillary channels at the seams leave a penetration path for waterborne stains, finally producing two problems: a drop in spray rating and seam wicking.

When wet pickup runs low, the finishing liquor spreads unevenly on the fibre surface and local grade drops appear first in the spray rating. KMF-4301 forms a continuous film; once the two readings of substrate grammage and wet pickup are set, its dosage is re-rated by pad pressure, and the spray rating returns to the acceptance grade.

After curing temperature is insufficient, the film is under-crosslinked and hydrostatic pressure resistance and the stain-resistance grade fall together. KMF-4301 forms a continuous film on the fibre surface; the two sets of readings, AATCC 22 spray rating against hydrostatic pressure resistance, and seam-wicking width against stain-resistance grade, are compared side by side, the addition is rated to the fitted grade of that batch, and the spray rating no longer falls round after round.

When substrate grammage reaches the upper limit, the path for the finishing liquor to penetrate into the fabric core lengthens and the uniformity of the film after curing falls in step. The KMF-4301 series causes no emulsion breaking in the same bath as the softener and adds no extra touch-up finishing rounds on this item; once the three readings of substrate grammage, wet pickup and curing temperature are brought together, the optimal dosage of that batch is settled and the finishing hall sets its process card at that grade.

Typical Operating Conditions and Verification

Customer case: the pad-dry-cure hall of a home-textile finishing plant in Hubei, applied to the water-repellent and stain-resistant finishing of upholstery and sofa fabrics.

Before the switch, the spray rating of rolled fabric needed touch-up finishing once every batch and seam wicking was repeatedly found at finished-goods inspection. After comparing substrate grammage and wet pickup, KMF-4301 was chosen, with the addition rated by curing temperature and pad pressure; AATCC 22 spray rating and hydrostatic pressure resistance were logged by batch, and seam-wicking width against stain-resistance grade formed a second side-by-side set. After the solution was in place, the spray rating returned to the acceptance grade; seam wicking was no longer found batch after batch, and touch-up finishing rounds were cut from once a batch to once every three batches.

Frequently Asked Questions

Will finishing the KMF-4301 series in the same bath as the softener weaken the water-repellency grade of the fabric?

Set the two readings of wet pickup and curing temperature side by side and the degree of film crosslinking can be read out. The KMF-4301 series forms a continuous film on the fibre surface and causes no emulsion breaking in the same bath as the softener; the measured data on AATCC 22 spray rating and hydrostatic pressure resistance are given by Chemi Tech from side-by-side measurement of the same finishing batch, and dosing at the rated magnitude does not change the original breathability rhythm of the fabric. The field dosage is fine-tuned again by substrate grammage, and Chemi Tech settles the fitted dosage of that batch from side-by-side measurement of the same batch.