Rows of industrial silos with numbers marked on their outer walls and neat top structures

After the roller-coating line speed is raised, the solvent-borne topcoat has no time to spread across the wet-film surface, transverse orange-peel streaks on the panel and edge retraction at the panel edges set together, the cross-cut results of interlayer adhesion fluctuate accordingly, and touch-up spraying and rework of the whole coil pin the coating-section schedule down at this step.

Chemi Tech has introduced the KMP-4105 series of levelling agents for the roller-coating levelling stage of solvent-borne coil coatings; the dosage is adjusted flexibly by line speed, wet-film thickness, flash-off temperature and baking curve. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the levelling window; its compatibility is excellent and it causes no craters, and it does not decompose or yellow in the baking section. The measured results of the orange-peel grade on the panel and the cross-cut adhesion grade are filed into the same test-panel record, and the fitted interval of that line is given in several grades by the combination of line speed and film thickness.

Advantages of Chemi Tech Levelling Agents

The Chemi Tech KMP-4105 series levelling agent is configured for the roller coating of solvent-borne coil coatings. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; the orange-peel grade on the panel rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters and not weakening interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass coating stable; and its thermal stability is strong, with no decomposition or yellowing in the baking section and little effect on panel gloss.

Industry Pain Points and Solutions

The root of orange peel in coil roller coating lies mostly in the combined effect of a too-short flash-off window and too-steep a surface-tension gradient across the wet film, while raising the line speed further compresses the spreading time, finally concentrating in two places: orange peel on the panel and edge retraction at the panel edges.

Once the line speed is raised, the wet film has no time to spread out within the flash-off window and the transverse orange-peel streaks set first. KMP-4105 markedly lowers the dynamic surface tension; once the line-speed and flash-off-temperature readings are set, its fitted dosage is re-rated by the coating tempo of that coil, and the orange-peel grade on the panel rises one notch.

When the wet-film thickness is set thicker, the surface-tension gradient at the panel edge amplifies, edge retraction follows, and the film thickness at corners falls in step. KMP-4101 performs consistently in spreading across both the thick-film and thin-film grades; once the wet-film thickness and baking-curve readings are checked together, the precise dosage is graded at once; by comparison, the edge-retraction width of the thick-film section falls into the same interval as that of the thin-film section, and the cross-cut adhesion results no longer fluctuate with film thickness.

With the temperature curve in the baking section, the most easily disturbed is the recoat interface of the two-pass coating. The KMP-4105 series leaves margin for recoatability and adds no extra sanding step on this item; with line speed, film thickness and flash-off all checked through, the fitted dosage of that line is settled within this interval, and the roller-coating unit runs by it.

Typical Operating Conditions and Verification

Customer case: the roller-coating workshop of a prepainted coil producer in Shandong, applied to the solvent-borne topcoat roller coating and baking stages.

Before the switch in this plant, transverse orange-peel streaks on the panel recurred on the same coil, edge retraction at the panel edges was especially obvious in the thick-film section, and the cross-cut results of the two-pass coating were good on some panels and poor on others. After comparison of line speed and wet-film thickness, KMP-4105 was adopted as the levelling grade for that line, with the dosage rated by flash-off temperature and baking curve. After commissioning, the front and rear sections of the same coil were logged side by side: the front section at the original dosage and the rear section at the rated dosage; the orange-peel grade of the front section still rebounded between two grades, while that of the rear section and the edge-retraction width converged; the cross-cut results of the thick-film section passed stably, and the number of touch-up-sprayed coils fell back.

Frequently Asked Questions

After the roller-coating line speed is raised, will increasing the levelling-agent dosage instead cause craters?

It depends entirely on whether the wet film spreads into place within the flash-off window. The KMP-4105 series has excellent compatibility and causes no craters at normal dosage, leaving margin at the recoat interface; the measured data on orange-peel grade and gloss readings are checked out by Chemi Tech from the test-panel records of the same roller-coating line. After line speed or wet-film thickness is adjusted, the actual dosage is re-calibrated to the new process card; Chemi Tech checks the test-panel records against the production-line data and gives the fitted dosage.