Fine powder heaped into a gentle slope on the bench

After the titanium dioxide grade is changed for the epoxy primer, the fineness reading of the color paste is slow to come down, flooding and floating show up together in the rub-out test, the same formulation has to be fully re-adjusted when the grade is switched, and the tinting lead time is pinned down at the grinding step.

Chemi Tech has introduced the KMK-410 series of dispersants for the wetting and dispersing of epoxy primers and industrial anticorrosive coatings; the dosage is adjusted flexibly by pigment grade, surface treatment and target solids content. The anchoring groups of this grade grip the pigment surface and do not desorb under high-shear grinding, and the viscosity-reduction effect is marked. The measured data on color-paste fineness readings and sand-mill current are tabulated grade by grade, and the dosage of that color range is confirmed category by category by the differences in grade and solids content.

Advantages of Chemi Tech Dispersants

The Chemi Tech KMK-410 series dispersant is configured for the wetting and dispersing of epoxy primers and industrial anticorrosive coatings. Its anchoring groups grip the pigment surface and do not desorb under high-shear grinding; the viscosity-reduction effect is marked, and the sand-mill current stays smooth and controllable; its adaptability to inorganic and organic pigments is broad, so switching grades does not require a full re-adjustment; its storage stability is strong, and the color paste neither reverts in fineness nor floods; it can anchor in both waterborne and solvent-borne systems, and the grinding power consumption per unit of color paste falls accordingly.

Industry Pain Points and Solutions

The root of flooding and floating in a tinting system lies mostly in a mismatch between the pigment surface treatment and the anchoring groups of the dispersant, while a rise in target solids content further compresses the interparticle spacing to a critical value, finally concentrating in two places: fineness rebound and flooding in the rub-out test.

Once the titanium dioxide grade is switched, the dispersant that had anchored well is pulled off course by the polarity of the new surface, and the fineness reading rebounds repeatedly near the pass line. KMK-410 runs anchoring comparisons by grade and surface treatment; with the two clues sorted out, its fitted dosage is rated grade by grade, and the fineness reading no longer rebounds.

When the target solids content is raised, the viscosity of the color paste pushes the sand-mill current up, the grinding time is forced longer, yet the fineness still cannot be brought down. KMK-412 performs consistently in viscosity reduction across both the low-to-medium and the high solids-content grades; once the target-solids-content and grinding-time readings are checked together, the precise dosage is graded at once; by comparison, the fineness reading of the high-solids color paste falls into the same interval as that of the low-to-medium-solids paste, and the sand-mill current no longer fluctuates widely with solids content.

With fineness reversion and settling during storage, the most easily disturbed is the number of re-grinding cycles. The KMK-410 series anchors adequately and adds no extra re-grinding cycles on this item; once grade, solids content and grinding time are all compared, the precise dosage of that color range is confirmed grade by grade, and the tinting center no longer carries out a full re-adjustment.

Typical Operating Conditions and Verification

Customer case: the tinting center of an industrial anticorrosive coatings producer in Shanghai, applied to the titanium dioxide sand-milling and paint-letdown stages of epoxy primers.

Before the switch in this plant, whenever the surface treatment of an incoming titanium dioxide batch differed, the fineness reading of the same formulation rebounded repeatedly near the pass line, and the rub-out flooding grade passed on only one of the batches. KMK-410 was used as the general dispersing grade for that center, with the dosage rated in grades by pigment grade and target solids content, and the grinding time and sand-mill current re-recorded grade by grade. After comparison, the high-solids batch and the low-to-medium-solids batch were logged side by side: the fineness reading of the former fell into the same interval as that of the latter, the flooding grades of the earlier and later batches all fell into the pass grade, and the sand-mill current no longer fluctuated widely from batch to batch; the number of re-grinding cycles decreased.

Frequently Asked Questions

After the titanium dioxide grade is switched for an epoxy primer, can the same dispersant still hold the fineness?

The approach is to bring the two clues, pigment surface treatment and target solids content, together. The KMK-410 series runs pigment-by-pigment anchoring comparisons by grade, with broad adaptability to inorganic and organic pigments; the measured data on fineness readings and rub-out flooding grades are given by Chemi Tech from pigment-by-pigment comparisons of the same color range. When the grade is switched or the target solids content is raised, the actual dosage takes these two items as correction terms; Chemi Tech gives the precise dosage of that color range from the pigment-by-pigment comparison results.