White steam dispersing sideways above the process area, with towers standing behind it

Microbubbles in the grinding vessel refuse to dissipate, slurry fineness readings rebound repeatedly around the acceptance line, sand-mill current rises and falls with the foam layer, and the colour-matching delivery schedule of the tinting section is pinned down at this grinding step.

Chemi Tech supplies the KM-270 series of defoamers for waterborne colour paste and coating slurry grinding systems; the dosage is adjusted flexibly by slurry solids content and grinding speed. This grade has good compatibility and disperses readily in the slurry, without separating out or floating under high-shear grinding; it causes no craters or fish eyes, and the appearance of the paint film is not impaired by the addition; the defoaming speed is high, and the foam layer in the grinding vessel falls back markedly. The measured data on foam-layer height in the grinding vessel and on slurry fineness readings are cross-checked together, and the fitted dosage of the KM-270 series is determined accordingly.

Advantages of Chemi Tech Defoamers

The Chemi Tech KM-270 series defoamer is configured for grinding waterborne colour pastes and coating slurries. Its compatibility is excellent and it disperses readily in the slurry, without separating out or agglomerating under high-shear grinding; its defoaming speed is high, and the foam layer in the grinding vessel falls back markedly; its foam-suppressing duration is long-lasting, noticeably reducing the top-up frequency across successive grinding batches; it causes no craters or fish eyes, leaving the paint-film appearance unaffected; its stability is strong, with no reversion to coarse particles and no layer separation while the slurry stands in the holding tank; and its dosage is economical, rated by slurry solids content, so the additive cost per grinding batch can be accounted directly.

Industry Pain Points and Solutions

The root of slurry foaming and fineness rebound lies mostly in the combined effect of air entrained by grinding shear and surfactants in the slurry; once the solids content is raised, the distance between particles is compressed, and the trouble finally concentrates in two problems: foam-layer height and fineness readings.

Once the grinding speed is raised, air is drawn into the slurry, the foam layer in the grinding vessel first builds up, and the fineness readings then rebound around the acceptance line. KM-270 defoams fast; with both the solids-content and speed readings set, its fitted dosage is re-rated for that batch, and the foam-layer height narrows to a controllable range.

When the slurry solids content is set higher, the distance between particles is compressed, the sand-mill current amplifies the viscosity change along with it, yet the fineness readings are slow to fall. KM-270 has excellent compatibility and performs stably across both thick-slurry and thin-slurry grades; once the solids-content reading and the sand-mill current are both set, the two sets of readings are compared side by side, the dosage is graded accordingly, and the fineness readings land within the acceptance line.

Residual microbubbles while the slurry stands in the holding tank are also within consideration. The KM-270 series is strongly stable and adds no extra regrinding runs on this item; once speed, solids content and standing time are all checked through, the fitted dosage of that grinding section is made clear and the fineness readings no longer rebound from batch to batch.

Typical Operating Conditions and Verification

Customer case: a waterborne colour paste producer in Anhui, applied to the colour-paste sand milling and slurry make-up stages.

After this plant changed pigment batch numbers, the fineness readings differed markedly across three batches, the foam-layer height in the grinding vessel fluctuated from batch to batch, and the sand-mill current swayed along with it. After comparing slurry solids content and grinding speed, KM-270 was dosed, with the addition rate of this grade rated by foam-layer height and sand-mill current. Before commissioning, the fineness readings and foam-layer height had long failed to agree; after commissioning, the two sets of readings converged, the sand-mill current returned to a steady range, residual microbubbles after standing in the holding tank fell markedly, and the number of regrinding runs dropped in step.

Frequently Asked Questions

Will long-term dosing of the KM-270 series into the slurry cause craters or affect the paint-film appearance?

The question has to be approached along two lines together: slurry solids content and grinding shear. The KM-270 series is a readily dispersible type that does not separate out or agglomerate under high shear; the measured data on foam-layer height and paint-film crater rating are given by Chemi Tech from controlled measurements on the same grinding batch, and within the rated dosage band they do not disturb the slurry's own colour development or storage. The actual addition rate is corrected by slurry solids content and grinding speed; Chemi Tech gives the fitted dosage of that section from controlled measurements on the same batch of slurry.