An oil refinery with its process units and tank farm spread out in an aerial view

A layer of fine foam floats up on the stripping tank surface, residues on the developed panel increase along with it, the bath changeover cycle of the cleaning section is shortened, and the shift output is pinned down at the rewash step.

Chemi Tech supplies the KM-192 series of defoamers for the developing, stripping and cleaning stages of printed circuit board production; the dosage is adjusted flexibly by developer concentration, bath temperature and spray pressure. This grade is a silicone-free formulation and leaves no silicone spots on the panel or tank walls; it resists acid and alkali, and its foam-suppressing power does not decay in either the alkaline-leaning or the acid-leaning range; its defoaming speed is high, and the foam layer on the tank surface falls back markedly after spraying. The measured data on the count of residual spots on the panel and on the bath foam-layer height are listed on the same record sheet; with the product chosen against different panel-cleanliness requirements, the precise dosage of the KM-192 series can be read off directly.

Advantages of Chemi Tech Defoamers

The Chemi Tech KM-192 series defoamer is configured for the developing, stripping and cleaning stages of circuit board production. Its silicone-free formulation leaves no silicone spots on the panel or tank walls; it resists acid and alkali, and its foam-suppressing power does not decay in either the stripping liquor or the cleaning liquor; its defoaming speed is high, and the foam layer on the tank surface falls back markedly after spraying; its foam-suppressing duration is long-lasting, noticeably reducing the bath top-up frequency; and its compatibility is excellent, so it does not separate out when coexisting with the developer or stripping liquor, and the bath changeover cycle is not shortened by the addition.

Industry Pain Points and Solutions

The root of tank-surface foaming and panel residues lies mostly in the combined effect of surfactant build-up in the developer and spray shear; once the temperature of the stripping stage is raised, the foam is stabilised at the liquid surface, and the trouble finally concentrates in two problems: the count of residual spots on the panel and the development defect rate.

When the developer concentration runs high, the tank-surface foam first covers the panel, residual spots after development increase along with it, and the line-width reading drifts first at the panel edge. KM-192 defoams fast; with both the concentration and bath-temperature readings set, its precise dosage is re-rated for that stage, and the count of residual spots on the panel falls back into the pass range.

After the stripping-stage temperature is raised, the foam layer settles stably at the liquid surface, residual resist film floats up with the foam, and the rinsing burden of the cleaning section is amplified along with it. KM-192 resists acid and alkali and performs stably across both the alkaline-leaning and acid-leaning ranges; once the bath-temperature and rinse-conductivity readings are compared side by side, the dosage is graded accordingly and the development defect rate returns within the acceptance line.

When the spray pressure is turned up, mechanical foam in the bath is stirred up repeatedly, and water marks and residues on the panel rise together. The KM-192 series has excellent compatibility and adds no extra rinsing runs on this item; once the three lines of concentration, temperature and pressure are checked through, the fitted dosage of that cleaning section is settled, the residual spots on the panel converge, and the section is commissioned at the rated band.

Typical Operating Conditions and Verification

Customer case: a circuit board manufacturer in Fujian, applied to the developing, stripping and cleaning stages.

After this plant changed its developer supplier, the count of residual spots on the panel differed markedly across three shifts, the foam-layer height on the tank surface fluctuated with spray pressure, and the bath changeover cycle shortened noticeably. After comparing panel-cleanliness requirements with bath conditions, KM-192 was chosen as the defoaming grade for that stage, with the addition rate rated by developer concentration and spray pressure. In the plant's earlier bath records the two sets of readings had long failed to agree and the rinsing runs were raised shift after shift; after commissioning, the two sets of readings converged, the rinsing runs returned to the original setting, the bath changeover cycle lengthened in step, and water marks at the panel edges no longer appeared in patches.

Frequently Asked Questions

Will long-term dosing of the KM-192 series into the cleaning stage leave silicone spots on the panel?

It depends on whether the amount of silicone introduced into the bath falls within the assessment scope of panel cleanliness. The KM-192 series is a silicone-free formulation; the measured data on the count of residual spots on the panel and on the bath foam-layer height are given by Chemi Tech from side-by-side comparisons of the same cleaning stage, and within the rated dosage band they do not disturb the dissolution rate of the developer or the line-width readings. The addition rate at commissioning is weighed separately by bath concentration and spray pressure; Chemi Tech determines the precise dosage from the measured panel residues and bath service life.