Columns and beams of a steel-structure workshop crossing in dim light
After the steel-structure topcoat reaches surface dry, the brush marks grow clearer instead; orange peel on the panel and edge retraction at the corners appear together on the same component, gloss uniformity falls in step, and rework touch-up spraying pins the coating schedule down at this step.
Chemi Tech supplies the KMP-4605 series of levelling agents for the flow and levelling of solvent-borne steel-structure topcoats; the dosage is adjusted flexibly by chain speed and solvent ratio. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the solvent release window; its compatibility is excellent, causing no craters and not weakening interlayer adhesion; and its thermal stability is strong, with no decomposition or yellowing in the baking section and little effect on gloss. The measured data on orange-peel grade and on gloss readings are filed into the same test-panel record, the topcoat appearance grades are divided accordingly, and the fitted dosage of the KMP-4605 series is settled on that line.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-4605 series levelling agent is configured for solvent-borne steel-structure topcoat application. It lowers the dynamic surface tension, letting the wet film spread fully within the solvent release window; the orange-peel grade on the panel rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters; its thermal stability is strong, with no decomposition or yellowing in the baking section and little effect on gloss; and it leaves margin for recoatability, keeping the interface of the two-pass topcoat stable, so the cross-cut result of interlayer adhesion stays consistent.
Industry Pain Points and Solutions
The root of orange peel and brush marks on a coating line lies mostly in the combined effect of a too-short solvent release window and too-steep a surface-tension gradient across the wet film; raising the chain speed further compresses the spreading time, and the trouble finally concentrates in two problems: orange peel on the panel and gloss uniformity.
Once the chain speed is raised, the wet film has no time to spread within the solvent release window, the brush marks set at once, and the panel gloss readings fall in step. KMP-4605 markedly lowers the dynamic surface tension; with both the chain-speed and solvent-ratio readings set, its fitted dosage is re-rated for that line, and the orange-peel grade on the panel rises one notch.
When the wet-film thickness is set thicker, the surface-tension gradient at the corners amplifies, edge retraction follows, and the film thickness at the component edges falls in step. KMP-4605 performs stably across both thick-film and thin-film grades; once the wet-film thickness and the baking curve are compared side by side, the addition rate is graded accordingly, and edge retraction at the panel edges basically no longer appears.
After the solvent ratio is changed, the recoat interface is the most easily disturbed. The KMP-4605 series leaves margin for recoatability and adds no extra sanding step on this item; once chain speed, film thickness and ratio are all checked through, the fitted dosage of that coating line is made clear, the gloss readings fall back into the same range, and the steel-structure line is graded accordingly.
Typical Operating Conditions and Verification
Customer case: a steel-structure component coating enterprise in Hebei, applied to the steel-structure topcoat spraying and baking stages.
After this plant changed its thinner, brush marks on the panel grew clearer at the surface-dry stage, the film-thickness reading at component edges was one notch lower than on the flat face, and gloss uniformity fluctuated markedly after baking. After comparing chain speed and solvent ratio, KMP-4605 was switched in as the levelling grade for that line, with the addition rate of this grade rated by wet-film thickness and baking temperature. After the switch, the brush marks on the panel spread out within the solvent release window, the film thickness at component edges converged with the flat face, the fluctuation in gloss readings narrowed, and the cross-cut result between the two topcoat passes was no longer good on some pieces and poor on others.
Frequently Asked Questions
After the chain speed is raised, will the KMP-4605 series thin down the recoat interface?
Chain speed, wet-film thickness and the solvent release window have to be brought together for comparison. After lowering the dynamic surface tension, the KMP-4605 series still stays compatible with the topcoat resin; the measured data on orange-peel grade and the film thickness at component edges are checked out by Chemi Tech from side-by-side test panels on the same coating line, and within the rated dosage band they do not weaken interlayer adhesion. The actual addition rate is weighed separately by chain speed and the baking curve; Chemi Tech checks the test-panel records of the same line and gives the fitted dosage.