Steel structural supports joined to cylindrical tank bodies within the plant area

After home-appliance shells come off the waterborne topcoat on the spray line, orange peel surfaces on the panel first and edge retraction follows at the corners, the interlayer adhesion of the two-pass spray is good on some panels and poor on others in the cross-cut test, and rework and touch-up spraying pin the shift throughput down at the coating step.

Chemi Tech has introduced the KMP-4510 series of levelling agents for the waterborne coating of home-appliance shells; the dosage is adjusted flexibly by wet-film thickness. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the flash-off window; its compatibility is excellent and it causes no craters, it leaves margin for recoatability, and its effect on gloss is small. The measured data on the orange-peel grade of the panel and the cross-cut adhesion grade are filed into the same test-panel record, and the fitted dosage of the KMP-4510 series is settled at this grade of that line; since the tempo and baking conditions differ from one coating line to another, the width of the levelling window is checked line by line by Chemi Tech against the test-panel data.

Advantages of Chemi Tech Levelling Agents

The Chemi Tech KMP-4510 series levelling agent is configured for the waterborne coating of home-appliance shells. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; its compatibility is excellent, causing no craters and not impairing interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass spray stable; and its thermal stability is strong, with no decomposition or yellowing in the baking section, and the panel gloss readings filed by line into the test-panel records.

Industry Pain Points and Solutions

The root of orange peel on home-appliance shell topcoats lies mostly in the combined effect of a too-short flash-off period and too-steep a surface-tension gradient across the wet film, while raising the line speed further compresses the time available for spreading, finally concentrating in two places: orange peel on the panel surface and edge retraction at the panel edges.

Once the chain speed is raised, the wet film has no time to spread within the flash-off window and the orange peel sets first, while the panel gloss reading falls in step. KMP-4510 markedly lowers the dynamic surface tension; once the two readings of spraying tempo and flash-off temperature are set, its fitted dosage is re-rated by the line speed of that line, and the orange-peel grade on the panel surface rises one notch.

When the wet-film thickness is set thicker, the surface-tension gradient at the panel edge amplifies, edge retraction follows, and the film thickness at corners falls in step. KMP-4510 performs stably across both the thick-film and thin-film grades; once the orange-peel-grade reading and the corner-film-thickness reading of the same test panel are brought together for comparison, the dosage is graded at once, edge retraction at the panel edges basically no longer appears, and gloss uniformity returns to the middle of the interval.

When the baking curve is changed, the most easily disturbed is the recoat interface between the two spray passes, and the cross-cut result of interlayer adhesion fluctuates accordingly. The KMP-4510 series leaves margin for recoatability and adds no extra sanding step on this item; once the three readings of tempo, film thickness and flash-off are checked through, the fitted dosage of that line is settled, and the coating line calibrates the scale of the on-line mixing tank by this grade.

Typical Operating Conditions and Verification

Customer case: the topcoat line of a home-appliance shell spraying enterprise in Guangdong, applied to the waterborne topcoat spraying and baking stages of home-appliance shells.

In this plant, edge retraction at the panel edges was not obvious, yet orange peel recurred on the same panel surface, the cross-cut results of the two-pass spray were good on some panels and poor on others, and the count of reworked and touch-up-sprayed parts accumulated shift by shift. KMP-4510 was switched in as the levelling grade for that line, with the addition rated by wet-film thickness and spraying tempo. After commissioning, the orange-peel grade on the panel surface rose one notch and edge retraction at the panel edges basically no longer appeared; the two sets of test-panel readings were given side by side in the same record, the cross-cut result of interlayer adhesion for the two-pass spray passed stably, and the shift plan of the coating section was completed to the original schedule.

Frequently Asked Questions

If the levelling-agent dosage is increased, will it instead cause craters or impair recoating?

What directly decides whether the panel surface craters is whether the wet film spreads sufficiently within the flash-off window. The KMP-4510 series has excellent compatibility and causes no craters at normal dosage; the measured data on orange-peel grade and gloss readings are checked out together by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The on-line dosage is re-checked line by line by chain speed and wet-film thickness; Chemi Tech determines the fitted dosage of that line from the measured data of test panels and production line laid side by side.