Coloured metal roof panels spread out in sheets as seen from above
On furniture vertical surfaces, the wet film enters flash-off before it has levelled, so sag streaks and recoat edge marks are left together in the topcoat, and the gloss reading and sanding-rework volume surface together at the off-line inspection.
Chemi Tech supplies the KMP-4100 series of levelling agents for vertical-surface spraying and recoating of waterborne furniture coatings; the dosage is adjusted flexibly by coating viscosity, spray volume and flash-off temperature. This grade lengthens the wet-film open time and lowers the surface-tension gradient before and after touch-dry, causes no flocculation with the waterborne resin or the thickener, and leaves intercoat sandability unaffected. The measured data on panel sag rating and gloss reading are compared side by side, and the fitted dosage of the KMP-4100 series is graded from them.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-4100 series levelling agent is configured for furniture and woodwork spraying stations. The wet-film open time is long, leaving ample spreading margin after vertical-surface spraying; compatibility is excellent, with no flocculation against the waterborne resin or the thickener; foam suppression is stable, so micro-bubbles in the circulating coating do not multiply as the spray volume rises; intercoat sandability is unaffected and recoat edge marks narrow clearly; the dosage is economical, rated in steps by coating viscosity; and the panel gloss reading after flash-off stays stable and controllable.
Industry Pain Points and Solutions
The root of sagging on vertical surfaces lies mostly in the combined effect of low coating viscosity and a heavy single-pass spray volume, while a short flash-off window further compresses the wet-film spreading time, finally producing two problems: sag streaks and recoat edge marks.
When coating viscosity runs low, sag streaks first appear in the vertical wet film under gravity and the panel sag rating climbs with it. KMP-4100 has a long open time; once the coating-viscosity and spray-volume readings are set, its dosage is re-rated by the vertical-surface area, and the sag rating falls back into the acceptance range.
After the spray volume is raised, wet-film thickness rises in step, and recoat edge marks and the panel gloss reading fall together. KMP-4100 lowers the surface-tension gradient before and after touch-dry; by comparing the two sets of data, panel sag rating against gloss reading, and wet-film thickness against the intercoat sanding grade, the dosage is rated to the fitted grade of that line, and the gloss reading no longer falls piece by piece.
When the flash-off temperature is pushed to its upper limit, premature touch-dry locks in the unlevelled marks and sanding-rework rounds increase in step. The KMP-4100 series causes no flocculation with the thickener and adds no extra intercoat re-inspections on this item; once the three readings of coating viscosity, spray volume and flash-off temperature are brought together, the precise dosage of that line is settled and the coating workshop draws up its process card at that grade.
Typical Operating Conditions and Verification
Customer case: the topcoat workshop of a solid-wood furniture maker in Anhui, applied to the cabinet vertical-surface spraying and recoating stages.
Before the switch, vertical-surface sagging often covered a whole batch of cabinet doors and recoat edge marks had to be rescued by sanding every shift. KMP-4100 was fitted to this class of spray line, with the dosage rated by coating viscosity and spray volume; the panel sag rating and gloss reading were logged per batch, and the wet-film thickness and intercoat sanding grade were compared as a separate set. After the programme was in place, the sag rating returned to the acceptance range; the gloss reading no longer fell piece by piece, and sanding-rework volume fell from thirty percent of a batch to ten percent.
Frequently Asked Questions
Will the KMP-4100 series, by lengthening the wet-film open time, slow down the intercoat sanding tempo of the topcoat?
It depends on whether the coating viscosity and flash-off temperature fall within the touch-dry window of that line. The KMP-4100 series causes no flocculation with the thickener; the measured data on panel sag rating and gloss reading are given by Chemi Tech from side-by-side measurements on the same spray section, and dosing at the rated magnitude does not change the resin's original film-forming rhythm. The field dosage takes the spray volume as a correction term, and Chemi Tech gives the fitted programme for that line from the side-by-side comparison.