Rolls of striped fabric stacked in rows, with clearly layered end faces
After repeated flexing and wet rubbing, the wicking rise height and the spray rating of shoe mesh fabric fall together, and re-washing and re-finishing pin the delivery date down at the finishing step.
Chemi Tech supplies the KMWF-102 series of water repellents for fluorine-free water-repellent finishing of shoe materials and fabrics; the dosage is adjusted flexibly by substrate grammage, wet pickup and curing temperature. This grade is fluorine-free, forms a continuous film on the fibre surface, does not seal the original breathability channels of the mesh, causes no demulsification when used in the same bath as the softener in the finishing liquor, and the film withstands repeated wet rubbing after curing. The measured data on the AATCC 22 spray rating and the wicking rise height are compared side by side, and the fitted dosage of the KMWF-102 series is graded from them.
Advantages of Chemi Tech Water Repellents
The Chemi Tech KMWF-102 series water repellent is configured for the finishing stations of shoe mesh and fabrics. It is a fluorine-free system, forming a continuous film without sealing the breathability channels; the spray rating is stable, with a controllable drop after repeated wet rubbing; wicking suppression is good, with capillary rise at the eyelets and seams clearly narrowed; compatibility is excellent, with no demulsification in the same bath as the softener; the dosage is economical, rated in steps by substrate grammage; and the mesh handle and crease recovery stay stable after curing.
Industry Pain Points and Solutions
The root of fluorine-free water-repellency decay lies mostly in the combined effect of low wet pickup and insufficient curing temperature, while the pores of the mesh leave channels for capillary rise, finally producing two problems: a drop in the spray rating and wicking beyond the limit.
When wet pickup runs low, the finishing liquor spreads unevenly on the mesh surface and the spray rating first shows local drops. KMWF-102 forms a continuous film; once the substrate-grammage and wet-pickup readings are set, its dosage is re-rated by padder pressure, and the spray rating returns to the acceptance grade.
When curing temperature is insufficient, the film is under-crosslinked and the wicking rise height and hydrostatic pressure resistance fall together. KMWF-102 forms a continuous film on the fibre surface; by comparing the two sets of readings, the AATCC 22 spray rating against the wicking rise height, and hydrostatic pressure resistance against the crease-recovery grade, the dosage is rated to the fitted grade of that batch, and the wicking height no longer rises round by round.
When substrate grammage is pushed to its upper limit, the path for the finishing liquor to penetrate the fabric core lengthens and the film uniformity after curing falls in step. The KMWF-102 series causes no demulsification in the same bath as the softener and adds no extra re-finishing rounds on this item; once the three readings of substrate grammage, wet pickup and curing temperature are brought together, the optimal dosage of that batch is settled and the finishing workshop draws up its process card at that grade.
Typical Operating Conditions and Verification
Customer case: the finishing workshop of a sports-shoe upper material maker in Shanxi, applied to the fluorine-free water-repellent finishing stage of shoe mesh.
Before the switch, the spray rating of the rolled mesh needed re-finishing once per batch and wicking beyond the limit was detected repeatedly at finished-goods inspection. KMWF-102 was chosen after comparison against substrate grammage and wet pickup, with the dosage rated by curing temperature and padder pressure; the AATCC 22 spray rating and wicking rise height were logged per batch, and hydrostatic pressure resistance and the crease-recovery grade were compared as a separate set. After the programme was in place, the spray rating returned to the acceptance grade; the wicking rise height no longer rose round by round, and re-finishing rounds fell from once per batch to once every three batches.
Frequently Asked Questions
Being fluorine-free, can the KMWF-102 series hold the spray rating on mesh after repeated wet rubbing?
It depends on whether the wet pickup and curing temperature fall within the crosslinking window of that batch. The KMWF-102 series forms a continuous film on the fibre surface and causes no demulsification in the same bath as the softener; the measured data on the AATCC 22 spray rating and the wicking rise height are given by Chemi Tech from side-by-side measurements on the same finishing batch, and dosing at the rated magnitude does not change the mesh's original breathability rhythm. The field dosage is fine-tuned further by substrate grammage, and Chemi Tech fixes the fitted dosage of that batch from side-by-side measurements on the same batch.