A narrow passage between plant buildings with metal facades on both sides

The topcoat on the colour-coating line enters the curing oven before it has spread after roller coating; transverse streaks and local craters are set into the panel surface, and the deviations in gloss readings and the weathering recheck show up together only at end-of-line inspection.

Chemi Tech has introduced the KMP-4045 series of levelling agents for the roller-coating and curing stages of colour-coated coil topcoats; the dosage is adjusted flexibly by coating viscosity, line speed and oven temperature zones. This grade widens the solvent-release window, lowers the surface-tension gradient before surface drying, does not compete with pigments or resins in the system for adsorption sites, and leaves interlayer adhesion and weathering resistance unaffected. The measured data on panel orange-peel grade and gloss readings are compared side by side, and the fitted dosage of the KMP-4045 series is graded from them.

Advantages of Chemi Tech Levelling Agents

The Chemi Tech KMP-4045 series levelling agent is configured for colour-coating roller coating and curing oven stations. Its solvent-release window is wide, so wet-film spreading stays uniform even when line speed fluctuates; its compatibility is excellent, with no competition for adsorption sites with pigments or resins; its foam suppression is stable, so microbubbles in the coating circulation tank do not multiply as line speed rises; interlayer adhesion is unaffected, so cross-cut test readings do not fall with dosing; the dosage is economical, graded by coating viscosity; and panel gloss readings stay stable and controllable after high-temperature curing.

Industry Pain Points and Solutions

The root of panel-surface defects in colour coating lies mostly in the combined effect of high coating viscosity and the line-speed gradient, while the time left for spreading before the wet film enters the curing oven is further compressed, finally producing two problems: transverse streaks and gloss drop.

When coating viscosity runs high, the wet film first leaves transverse streaks at the roller-coater head outlet and the panel orange-peel grade rises in step. KMP-4045 has a wide release window; once the two readings of coating viscosity and line speed are set, its dosage is re-rated by coating weight, and the orange-peel grade falls back into the acceptance range.

After line speed is raised, wet-film spreading time is compressed and local craters and falling panel gloss readings appear together. KMP-4045 lowers the surface-tension gradient before surface drying; the two sets of data, panel orange-peel grade against gloss readings, and wet-film thickness against cross-cut adhesion grade, are compared side by side, the addition is rated to the fitted grade of that line, and gloss readings no longer fall coil after coil.

When the oven temperature zones reach the upper limit, premature surface drying fixes the unlevelled marks and recoating rounds increase in step. The KMP-4045 series does not compete with resins for adsorption sites and adds no extra weathering recheck on this item; once the three readings of coating viscosity, line speed and oven temperature zones are brought together, the precise dosage of that line is settled and the colour-coating hall sets its process card at that grade.

Typical Operating Conditions and Verification

Customer case: the coating hall of a colour-coated steel sheet producer in Tianjin, applied to topcoat roller coating and curing oven stages.

Before the switch in this enterprise, transverse streaks on the panel often covered the whole coil and the oven setting had to be lowered once for every coil because of gloss readings. KMP-4045 was fitted to that colour-coating line, with the addition rated by coating viscosity and line speed; panel orange-peel grade and gloss readings were logged by coil, and wet-film thickness against cross-cut adhesion grade formed a second side-by-side set. After the solution was in place, the orange-peel grade returned to the acceptance range; gloss readings no longer fell coil after coil, and recoating rounds were cut from twice a week to once a week.

Frequently Asked Questions

Will dosing the KMP-4045 series on a high-speed colour-coating line weaken the interlayer adhesion between topcoat and primer?

It is governed by whether coating viscosity and oven temperature zones fall within the curing window of that line. The KMP-4045 series does not compete with resins for adsorption sites; the measured data on panel orange-peel grade and gloss readings are given by Chemi Tech from controlled side-by-side measurement of the same coating section, and dosing at the rated magnitude does not change the original level of interlayer adhesion. The field dosage is corrected by line speed and wet-film thickness, and Chemi Tech settles the fitted scheme of that line from the side-by-side comparison.