Blue and orange metal panel surfaces separated along diagonal stripes
After the waterborne industrial topcoat passes through roller coating, edge retraction appears at the panel edges first and orange peel then shows across the panel surface; the interlayer adhesion of the two-pass coating fails the cross-cut test, and rework and touch-up pin the shift's throughput down at the coating step.
Chemi Tech has introduced the KMP-1205 series of levelling agents for the roller coating and levelling of waterborne industrial topcoats; the dosage is adjusted flexibly by roller-coating line speed and wet-film thickness. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the flash-off window; its compatibility is excellent and it causes no craters, it leaves margin for recoatability, and its interference with topcoat gloss is low. The measured data on panel orange-peel grade and the cross-cut result of interlayer adhesion are filed into the same test-panel record, and the mixing ratio is given separately by line speed and film thickness.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-1205 series levelling agent is configured for waterborne industrial topcoat roller-coating lines. It lowers the dynamic surface tension, letting the wet film spread fully within the flash-off window; edge retraction at the panel edges basically does not appear, with uniform corner coverage; the orange-peel grade on the panel surface rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters and not impairing interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass roller coating stable; and its thermal stability is strong, with no decomposition or yellowing in the baking section and interference with topcoat gloss kept low.
Industry Pain Points and Solutions
The root of orange peel on a roller-coated topcoat lies mostly in the combined effect of a too-short flash-off window and a too-steep surface-tension gradient across the wet film, while a rise in line speed further compresses the spreading time, finally concentrating in two places: orange peel on the panel surface and edge retraction at the panel edges.
Once the roller-coating line speed is raised, the wet film has no time to spread within the flash-off window and the orange peel sets first. KMP-1205 markedly lowers the dynamic surface tension; once the two readings of line speed and flash-off temperature are set, its dosage is re-rated by the tempo of that line, and the orange-peel grade on the panel surface rises one notch.
When the wet-film thickness is set thicker, the surface-tension gradient at the panel edge amplifies and edge retraction follows, while the film thickness at corners falls in step. KMP-1205 performs stably across both thick-film and thin-film grades; the two sets of results, panel orange-peel grade and cross-cut adhesion grade, are filed into the same test-panel record, the addition is graded accordingly, and edge retraction at the panel edges basically no longer appears.
After the baking curve is changed, the recoat interface is easily disturbed. KMP-1205 leaves margin for recoatability and adds no extra sanding step on this item; once the three sets of data, line speed, film thickness and flash-off, are brought together, the fitted dosage of that line is settled and the coating line completes the shift schedule at that grade.
Typical Operating Conditions and Verification
Customer case: an industrial coating enterprise in Guangdong, applied to the roller-coating and levelling stages of a waterborne industrial topcoat.
Edge retraction at the panel edges was not obvious, yet orange peel recurred on the same panel surface; gloss uniformity stayed low after baking; and the cross-cut result of the two-pass roller coating was good on some panels and poor on others. KMP-1205 was selected as the levelling agent for that line, with the addition rated by roller-coating line speed and wet-film thickness; the plant logged the two sets of results, panel orange-peel grade and cross-cut adhesion grade, into the same test-panel record. After the solution was in place, the orange-peel grade on the panel surface rose one notch, edge retraction at the panel edges basically no longer appeared, the cross-cut result of interlayer adhesion for the two-pass roller coating passed stably, the count of reworked and touch-up parts fell back, and the coating section's shift plan was completed on schedule.
Frequently Asked Questions
If the levelling-agent dosage is increased, will it instead cause craters or impair recoating?
What is compared together are the two sets of readings, roller-coating line speed and the wet-film flash-off window. The KMP-1205 series has excellent compatibility, causes no craters at normal dosage, and leaves margin at the recoat interface; the measured data on orange-peel grade and gloss readings are checked out by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The application rate is rechecked line by line by roller-coating line speed and wet-film thickness, and Chemi Tech gives the fitted dosage of that line after checking the test-panel records against the production-line data.