End faces of rolled metal mesh material stacked in rows inside a warehouse
After the topcoat of the colour-coating line is roll-applied, transverse orange peel emerges at the panel edges first, the wet film has no time to spread in the flash-off section, the interlayer adhesion of the two-pass coating is good on some cross-cut tests and poor on others, and re-coating and reduced line speed pin the shift's output down at the coating stage.
Chemi Tech supplies the KMP-1410 series of levelling agents for roll-coating the topcoat of colour-coated coil; the dosage can be adjusted flexibly by roll-coating line speed. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the flash-off window; its compatibility is excellent and it causes no craters, while leaving margin at the recoat interface. The measured data for the orange-peel grade on the panel surface and the cross-cut result of interlayer adhesion are listed by line speed, and the fitted dosage of the KMP-1410 series can be read off grade by grade; the dosing range of that line is graded by line speed and film thickness, and the production line uses it by grade.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-1410 series levelling agent is configured for roll-coating the topcoat of colour-coated coil. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; the orange-peel grade on the panel surface rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters and giving uniform coverage at edges and corners; its thermal stability is strong, with no decomposition or yellowing in the baking section; the dosage is economical, rated by roll-coating line speed, so the additive cost per tonne of coil can be accounted coil by coil; and it leaves margin for recoatability, keeping the interface of the two-pass roll-coated topcoat stable.
Industry Pain Points and Solutions
The root of orange peel in roll coating lies mostly in the combined effect of a too-short flash-off window and a too-steep surface-tension gradient across the wet film, while raising the line speed compresses the spreading time further, finally concentrating in two places: orange peel on the panel surface and interlayer adhesion.
Once the roll-coating line speed is raised, the wet film has no time to spread in the flash-off window and the transverse orange peel sets first, with gloss on the panel surface mottling accordingly. KMP-1410 markedly lowers the dynamic surface tension; once the two readings of line speed and flash-off temperature are set, its dosage is re-rated by the chain speed of that line, and the orange-peel grade on the panel surface rises one notch.
When the wet-film thickness is set thicker, the surface-tension gradient at the panel edge amplifies, edge retraction follows, and the film thickness at corners falls in step. KMP-1410 performs stably across both thick-film and thin-film grades; once the two readings of wet-film thickness and baking curve are set, the dosage is graded accordingly, the edge film-thickness deviation narrows from 18% to 6%, and the orange-peel grade on the panel surface rises from grade 3 to grade 2, with both sets of readings checked on the same sheet.
Once the baking curve is changed, the most easily disturbed is the recoat interface. The KMP-1410 series leaves margin for recoatability and adds no extra sanding step on this item; once line speed, film thickness and flash-off are all checked through, the fitted range of that line is settled and the roll-coating section uses it by grade.
Typical Operating Conditions and Verification
Customer case: a colour-coated steel sheet manufacturer in Jiangsu, applied to topcoat roll-coating and baking levelling.
The plant had repeatedly detected transverse orange peel on the same coil, gloss uniformity stayed low after baking, and the cross-cut result of the two-pass coating was good on some panels and poor on others. KMP-1410 was selected as the levelling grade for that line, with the addition rate rated by roll-coating line speed and wet-film thickness. After the switch, the orange-peel grade on the panel surface rose from grade 3 to grade 2; the edge film-thickness deviation narrowed from 18% to 6%; the cross-cut result of the two-pass coating passed stably, the number of re-coated coils fell back, and the coating section's shift plan was completed to the original schedule.
Frequently Asked Questions
If the dosage of the KMP-1410 series is increased, will it instead cause craters or impair recoating?
It depends on the ratio between the roll-coating line speed and the wet-film surface tension, which determines whether spreading is sufficient. The KMP-1410 series has excellent compatibility and causes no craters at normal dosage, leaving margin at the recoat interface; the measured data for orange-peel grade and gloss readings are checked out by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The actual addition rate of that line is calibrated separately by line speed and film thickness, and the fitted range is defined by Chemi Tech from the test-panel records and production-line readings together.