The raised textured surface of a patterned steel plate seen at close range
After the topcoat spraying on the appliance-panel color coating line is finished, orange peel floats on the panel surface first, edge retraction follows at the corners, the interlayer adhesion of the two coats fails the cross-cut test, and rework and touch-up spraying pin the throughput down at the coating step.
Chemi Tech supplies the KMP-1608 series of leveling agents for appliance-panel color coating lines; the dosage is adjusted flexibly by chain speed, wet-film thickness and the flash-off window. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully within the flash-off window; its compatibility is excellent and it causes no craters, while leaving margin for recoatability. The measured results of the panel orange-peel grade and the cross-cut adhesion grade are filed into the same test-panel record, and the fitted dosage of the KMP-1608 series is settled at that grade of the line.
Advantages of Chemi Tech Levelling Agents
The Chemi Tech KMP-1608 series leveling agent is configured for appliance-panel color coating lines. It lowers the dynamic surface tension and lets the wet film spread fully within the flash-off window; edge retraction at the panel edges basically no longer appears, with even corner coverage; the panel orange-peel grade rises and gloss uniformity improves in step; its compatibility is excellent, causing no craters and not affecting interlayer adhesion; it leaves margin for recoatability, keeping the interface of the two-pass spray stable; its thermal stability is strong, with no decomposition or yellowing in the baking section; and the dosage is rated by chain speed, so the rework loss of the coating line can be accounted batch by batch.
Industry Pain Points and Solutions
The root of orange peel on a color coating line lies mostly in the combined effect of a too-short flash-off window and too-steep a surface-tension gradient across the wet film, while a higher chain speed compresses the spreading time further, finally concentrating in two places: orange peel on the panel surface and edge retraction at the panel edges.
Once the chain speed is raised, the wet film has no time to spread within the flash-off window and the orange peel sets first. KMP-1608 markedly lowers the dynamic surface tension; once the tempo and the flash-off temperature are set, its dosage is re-rated by the chain speed of that line, and the panel orange-peel grade rises one notch.
When the wet-film thickness is set thicker, the surface-tension gradient at the panel edge amplifies, edge retraction follows and the film thickness at the corners falls in step. KMP-1608 performs stably across both thick-film and thin-film grades; with the two sets of readings compared side by side, the chain speed rises from 80 metres per minute to 110, the panel orange-peel grade rises from grade 3 to grade 4, and edge retraction at the panel edges basically no longer appears.
Once the baking curve is changed, the first thing disturbed is the recoat interface. The KMP-1608 series leaves margin for recoatability and adds no extra sanding step on this item; with tempo, film thickness and flash-off all checked through, the fitted dosage of that line is settled and the coating shift crew executes at that grade.
Typical Operating Conditions and Verification
Customer case: the color coating line of an appliance-panel manufacturer in Jiangsu, applied to the topcoat spraying and baking stages.
At that plant orange peel recurred on the same batch of panels, gloss uniformity stayed low after baking, and the cross-cut result of the two-pass spray was good on some panels and poor on others. KMP-1608 was chosen as the leveling grade for that line, with the amount rated by chain speed and wet-film thickness. Measured performance after the switch: the panel orange-peel grade rose one notch; edge retraction at the panel edges basically no longer appeared; the cross-cut result of interlayer adhesion for the two-pass spray passed stably; and the count of reworked and touch-up parts fell back.
Frequently Asked Questions
Will raising the leveling-agent dosage instead cause craters or weaken the interlayer adhesion?
The key is whether the wet film spreads sufficiently within the flash-off window. The KMP-1608 series has excellent compatibility and causes no craters at normal dosage, leaving margin at the recoat interface; the measured data of the orange-peel grade and the gloss readings are checked out by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The actual dosage is re-calibrated by chain speed and wet-film thickness; Chemi Tech checks the test-panel results against the production-line records and gives the fitted dosage.