Circular tanks in a process area meeting white steam in dim light

After air is entrained in the grinding and let-down stages of a waterborne wood coating, the microfoam in the paint lingers, pinholes and craters appear on the roller-coated panel in step, the rub-up and gloss readings deviate together, and the rework volume of a batch of furniture topcoat is pinned down at this single compounding step.

Chemi Tech supplies the KM-263 series of defoamers for the grinding and let-down stages of waterborne wood coating enterprises; the dosage is adjusted flexibly by grinding speed, paint viscosity, roller-coating method and emulsion type. This grade has excellent compatibility: it causes neither craters nor fish eyes, and the microfoam can be brought under control in both stages; the measured data of the microfoam count in the paint and the pinhole count on the roller-coated panel are tabulated separately, and the fitted dosage of each of the two stages is settled respectively.

Advantages of Chemi Tech Defoamers

The Chemi Tech KM-263 series defoamer is configured for the grinding and let-down stages of waterborne wood coatings. Its compatibility is excellent, causing neither craters nor fish eyes; it removes microfoam effectively, noticeably reducing the pinhole count on the roller-coated panel; it has little effect on gloss, leaving the paint neither cloudy nor hazy; its foam-suppressing duration is long-lasting, so neither the grinding nor the let-down stage needs repeated make-up dosing; its thermal stability is strong, with no decomposition or volatilisation in the drying section; and the dosage is rated separately for the two stages, so the additive cost per tonne of paint is diluted across batches.

Industry Pain Points and Solutions

The root of foaming in the compounding of waterborne wood coatings lies mostly in the combined effect of air entrained by high shear in the grinding stage and a too-steep surface tension in the let-down stage, while insufficient wetting by the resin system locks the microfoam inside the paint, finally concentrating in two places: pinholes after roller coating and gloss deviation.

Once the shear in the grinding stage is raised, the paint entrains air into fine bubbles; before the fineness reading has fallen into the pass range, the microfoam has already built up. KM-263 removes microfoam effectively; once the two readings of grinding speed and paint temperature are cleared, the dosage is re-rated by the grinding load, and the microfoam count falls accordingly.

After the viscosity in the let-down stage is raised, the fine bubbles are hindered from rising and pinholes appear in clusters on the roller-coated panel. KM-263 has excellent compatibility; with the two sets of readings of paint viscosity and roller-coating speed checked side by side, the dosage is rated to the fitted grade of that stage, and the pinhole count falls within the pass line.

When the paint stands in the let-down tank, the microfoam lingers and the gloss reading deviates in step. This grade has a long-lasting foam-suppressing effect and adds no extra re-tanking frequency on this item; with speed, viscosity and roller-coating speed all checked through, the fitted dosage of that line is settled, and the coating workshop doses by that grade.

Typical Operating Conditions and Verification

Customer case: the furniture-paint compounding workshop of a waterborne wood coating enterprise in Zhejiang, applied to defoaming in the grinding and let-down stages.

After this plant changed to a new batch of emulsion, pinholes appeared in clusters on the roller-coated panel in spot checks, and the microfoam count of the same batch of paint differed markedly between the grinding and let-down stages. KM-263 was set as the defoaming grade for the let-down stage, with the dosage rated separately by grinding speed and paint viscosity. The measured data of the two stages are compared side by side: in the grinding stage the microfoam count fell from 31 per millilitre to 9, and in the let-down stage from 42 per millilitre to 12; the pinhole count on the roller-coated panel narrowed accordingly, the gloss reading of the topcoat returned to the pass range, and the number of reworked parts was absorbed within the shift plan.

Frequently Asked Questions

When a defoamer is added to a waterborne wood coating, can microfoam and pinholes be predicted?

What can be worked out clearly are the microfoam counts and pinhole readings at the grinding and let-down stages. The KM-263 series has excellent compatibility and causes no craters; the measured data of microfoam count and pinhole count on the roller-coated panel are checked out stage by stage by Chemi Tech on the same compounding line, and the trends of decay and rebound can be traced separately for the two stages, with the specific values subject to the paint conditions of that workshop. The actual dosage is further weighed by paint viscosity and roller-coating speed; Chemi Tech determines the fitted dosage from the stage-by-stage comparison.