Fine granular texture on a light cyan metal panel surface spread out in close view

When the surface-tension gradient cannot develop during the baking and levelling stage of a powder coating, orange peel appears in clusters on the panel surface and craters at the edges and corners, interlayer adhesion fails the cross-cut test, and the number of reworked parts on the powder-spray line pins the shift plan down at this single curing step.

Chemi Tech supplies the KMP-2201 series of levelling agents for the baking and levelling stage of powder coatings; the dosage is adjusted flexibly by the applied film thickness. This grade markedly lowers the dynamic surface tension, letting the wet film spread fully in the melt stage, and its compatibility is excellent without causing craters; the measured records of the orange-peel grade on the panel surface and the cross-cut adhesion grade are filed in the same test-panel record, and the fitted grade of that line is determined from them.

Advantages of Chemi Tech Levelling Agents

The Chemi Tech KMP-2201 series levelling agent is configured for the baking and levelling of powder coatings. It lowers the surface tension markedly, letting the powder film spread fully in the melt stage; the orange-peel grade improves and the undulation on the panel surface flattens out; its compatibility is excellent, causing no craters and not impairing interlayer adhesion; corner coverage is uniform and edge retraction at the thick-film grade basically no longer appears; its thermal stability is strong, with no decomposition or yellowing within the baking window; and the dosage is adjusted by film thickness and the baking curve, so the levelling investment per tonne of powder can be checked against the test-panel records.

Industry Pain Points and Solutions

The root of problems in the baking and levelling of powder coatings lies mostly in the combined effect of a too-gentle surface-tension gradient after the powder film melts and a too-short baking window, while uneven film thickness locks the orange peel and craters onto the panel surface, finally concentrating in two places: orange peel on the panel surface and craters at the edges and corners.

Once the applied film thickness is set thicker, the powder film does not spread sufficiently in the melt stage and the orange peel sets first. KMP-2201 lowers the surface tension markedly; once the two readings of film thickness and baking temperature are cleared, the dosage is re-rated by the load of that line, and the orange-peel grade rises one notch.

When the baking temperature is set too low, the crosslinking window narrows and edge retraction follows. KMP-2201 has excellent compatibility; with the two sets of readings of the panel's orange-peel grade and cross-cut adhesion grade checked side by side, the dosage is rated to the fitted grade of that line, and edge retraction basically no longer appears.

Once the chain speed of the oven is raised, the spreading time is compressed further and interlayer adhesion is the easiest thing to lose. This grade has strong thermal stability and adds no extra reworked parts on this item; with film thickness, temperature and chain speed all checked through, the fitted dosage of that line is determined, and the coating team executes by the record.

Typical Operating Conditions and Verification

Customer case: the coating line of a powder coating enterprise in Hebei, applied to the powder-application and baking-levelling stages.

Before this, orange peel on the panel surface recurred within the same oven batch, edge retraction was more concentrated on thick-film workpieces, and the spot-check results of cross-cut adhesion were good on some samples and poor on others. KMP-2201 was adopted as the levelling grade for that line, with the dosage rated by film thickness and baking temperature. The test-panel records list the readings of two grades side by side: at the thin-film grade the orange-peel grade rose from 3 to 5, and at the thick-film grade from 2 to 4; edge retraction basically no longer appeared, cross-cut adhesion passed stably, the number of re-sprayed parts fell, and the oven chain speed was kept at its original setting.

Frequently Asked Questions

If the dosage of a powder-coating levelling agent is increased, will it instead impair interlayer adhesion?

It all depends on whether the powder film spreads sufficiently within the melt window. The KMP-2201 series has excellent compatibility and causes no craters at normal dosage; the measured data of orange-peel grade and cross-cut adhesion grade are checked out together by Chemi Tech from the test-panel records of the same coating line, and within the above comparison range they do not weaken interlayer adhesion. The actual dosage is further calibrated by film thickness and baking temperature; Chemi Tech checks the test-panel results against the oven-temperature records and gives the fitted dosage.